Table 3 to Subpart GGGGG of Part 63—Applicability of General Provisions to Subpart GGGGG

- Table 3 to Subpart GGGGG of Part 63—Applicability of General Provisions to Subpart GGGGG

As stated in § 63.7940, you must comply with the applicable General Provisions requirements according to the following table:

Citation	Subject	Brief description	Applies to subpart GGGGG	§ 63.1	Applicability	Initial Applicability Determination; Applicability After Standard Established; Permit Requirements; Extensions, Notifications	Yes.	§ 63.2	Definitions	Definitions for part 63 standards	Yes.	§ 63.3	Units and Abbreviations	Units and abbreviations for part 63 standards	Yes.	§ 63.4	Prohibited Activities	Prohibited Activities; Compliance date; Circumvention, Severability	Yes.	§ 63.5	Construction/Reconstruction	Applicability; applications; approvals	Yes.	§ 63.6(a)	Applicability	General Provisions (GP) apply unless compliance extension GP apply to area sources that become major	Yes.	§ 63.6(b)(1)-(4)	Compliance Dates for New and Reconstructed sources	Standards apply at effective date; 3 years after effective date; upon startup; 10 years after construction or reconstruction commences for 112(f)	Yes.	§ 63.6(b)(5)	Notification	Must notify if commenced construction or reconstruction after proposal	Yes.	§ 63.6(b)(6)	[Reserved]			§ 63.6(b)(7)	Compliance Dates for New and Reconstructed Area Sources That Become Major	Area sources that become major must comply with major source standards immediately upon becoming major, regardless of whether required to comply when they were an area source	Yes.	§ 63.6(c)(1)-(2)	Compliance Dates for Existing Sources	Comply according to date in subpart, which must be no later than 3 years after effective date. For 112(f) standards, comply within 90 days of effective date unless compliance extension	Yes.	§ 63.6(c)(3)-(4)	[Reserved]			§ 63.6(c)(5)	Compliance Dates for Existing Area Sources That Become Major	Area sources that become major must comply with major source standards by date indicated in subpart or by equivalent time period (for example, 3 years)	Yes.	§ 63.6(d)	[Reserved]			§ 63.6(e)(1)-(2)	Operation & Maintenance		No, see § 63.7935(b).	§ 63.6(e)(3)	Startup, Shutdown, and Malfunction Plan (SSMP)		No, see § 63.7935(c).	§ 63.6(f)(1)	Compliance Except During SSM		No, see § 63.7935(b).	§ 63.6(f)(2)-(3)	Methods for Determining Compliance	Compliance based on performance test, operation and maintenance plans, records, inspection	Yes.	§ 63.6(g)(1)-(3)	Alternative Standard	Procedures for getting an alternative standard	Yes.	§ 63.6(h)	Opacity/Visible Emissions (VE) Standards	Requirements for opacity and visible emissions limits	No. No opacity standards.	§ 63.6(i)(1)-(14)	Compliance Extension	Procedures and criteria for Administrator to grant compliance extension	Yes.	§ 63.6(j)	Presidential Compliance Exemption	President may exempt source category from requirement to comply with final rule	Yes.	§ 63.7(a)(1)-(2)	Performance Test Dates	Dates for Conducting Initial Performance Testing and Other Compliance Demonstrations. Must conduct 180 days after first subject to final rule	Yes.	§ 63.7(a)(3)	CAA Section 114 Authority	Administrator may require a performance test under CAA section 114 at any time	Yes.	§ 63.7(b)(1)	Notification of Performance Test	Must notify Administrator 60 days before the test	Yes.	§ 63.7(b)(2)	Notification of Rescheduling	If rescheduling a performance test is necessary, must notify Administrator 5 days before scheduled date of rescheduled date	Yes.	§ 63.7(c)	Quality Assurance/Test Plan	Requirement to submit site-specific test plan 60 days before the test or on date Administrator agrees with: Test plan approval procedures; performance audit requirements; internal and external QA procedures for testing	Yes.	§ 63.7(d)	Testing Facilities	Requirements for testing facilities	Yes.	§ 63.7(e)(1)	Conditions for Conducting Performance Tests	Performance tests must be conducted under representative conditions. Cannot conduct performance tests during SSM. Not a violation to exceed standard during SSM	No, see § 63.7941(b)(2).	§ 63.7(e)(2)	Conditions for Conducting Performance Tests	Must conduct according to rule and EPA test methods unless Administrator approves alternative	Yes.	§ 63.7(e)(3)	Test Run Duration	Must have three test runs of at least one hour each. Compliance is based on arithmetic mean of three runs. Conditions when data from an additional test run can be used	Yes.	§ 63.7(f)	Alternative Test Method	Procedures by which Administrator can grant approval to use an alternative test method	Yes.	§ 63.7(g)	Performance Test Data Analysis	Must include raw data in performance test report. Must submit performance test data 60 days after end of test with the Notification of Compliance Status. Keep data for 5 years	Yes.	§ 63.7(h)	Waiver of Tests	Procedures for Administrator to waive performance test	Yes.	§ 63.8(a)(1)	Applicability of Monitoring Requirements	Subject to all monitoring requirements in standard	Yes.	§ 63.8(a)(2)	Performance Specifications	Performance Specifications in appendix B of part 60 apply	Yes.	§ 63.8(a)(3)	[Reserved]			§ 63.8(a)(4)	Monitoring with Flares	Unless your rule says otherwise, the requirements for flares in 63.11 apply	Yes.	§ 63.8(b)(1)	Monitoring	Must conduct monitoring according to standard unless Administrator approves alternative	Yes.	§ 63.8(b)(2)-(3)	Multiple Effluents and Multiple Monitoring Systems	Specific requirements for installing monitoring systems. Must install on each effluent before it is combined and before it is released to the atmosphere unless Administrator approves otherwise. If more than one monitoring system on an emissions point, must report all monitoring system results, unless one monitoring system is a backup	Yes.	§ 63.8(c)(1)	Monitoring System Operation and Maintenance	Maintain monitoring system in a manner consistent with good air pollution control practices	Yes.	§ 63.8(c)(1)(i)	Monitoring System Operation	Operate and maintain system as specified in § 63.6(e)(1)	No, see § 63.7935(b).	§ 63.8(c)(1)(ii)	Monitoring System Repair	Keep part for routine repairs available	Yes.	§ 63.8(c)(1)(iii)	Monitoring System SSM Plan	Develop an SSM Plan for the monitoring system	No, see § 63.7935(h)(1).	§ 63.8(c)(2)-(3)	Monitoring System Installation	Must install to get representative emissions and parameter measurements. Must verify operational status before or at performance test	Yes.	§ 63.8(c)(4)	Continuous Monitoring System (CMS) Requirements	CMS must be operating except during breakdown, out-of-control, repair, maintenance, and high-level calibration drifts	No.	§ 63.8(c)(4)(i)-(ii)	Continuous Monitoring System (CMS) Requirements	COMS must have a minimum of one cycle of sampling and analysis for each successive 10-second period and one cycle of data recording for each successive 6-minute period. CEMS must have a minimum of one cycle of operation for each successive 15-minute period	Yes. However, COMS are not applicable. Requirements for CPMS are listed in §§ 63.7900 and 63.7913.	§ 63.8(c)(5)	COMS Minimum Procedures	COMS minimum procedures	No.	§ 63.8(c)(6)	CMS Requirements	Zero and High level calibration check requirements	Yes. However requirements for CPMS are addressed in § 63.7927.	§ 63.8(c)(7)-(8)	CMS Requirements	Out-of-control periods, including reporting	Yes.	§ 63.8(d)	CMS Quality Control	Requirements for CMS quality control, including calibration, etc. Must keep quality control plan on record for 5 years. Keep old versions for 5 years after revisions	Yes.	§ 63.8(e)	CMS Performance Evaluation	Notification, performance evaluation test plan, reports	Yes.	§ 63.8(f)(1)-(5)	Alternative Monitoring Method	Procedures for Administrator to approve alternative monitoring	Yes.	§ 63.8(f)(6)	Alternative to Relative Accuracy Test	Procedures for Administrator to approve alternative relative accuracy tests for CEMS	No.	§ 63.8(g)(1)-(4)	Data Reduction	COMS 6-minute averages calculated over at least 36 evenly spaced data points. CEMS 1-hour averages computed over at least four equally spaced data points	Yes. However, COMS are not applicable. Requirements for CPMS are addressed in §§ 63.7900 and 63.7913.	§ 63.8(g)(5)	Data Reduction	Data that cannot be used in computing averages for CEMS and COMS	No.	§ 63.9(a)	Notification Requirements	Applicability and State Delegation	Yes.	§ 63.9(b)(1)-(5)	Initial Notifications.	Submit notification 120 days after effective date. Notification of intent to construct/reconstruct; Notification of commencement of construct/reconstruct; Notification of startup. Contents of each	Yes.	§ 63.9(c)	Request for Compliance Extension	Can request if cannot comply by date or if installed BACT/LAER	Yes.	§ 63.9(d)	Notification of Special Compliance Requirements for New Source	For sources that commence construction between proposal and promulgation and want to comply 3 years after effective date	Yes.	§ 63.9(e)	Notification of Performance Test	Notify Administrator 60 days prior	Yes.	§ 63.9(f)	Notification of VE/Opacity Test	Notify Administrator 30 days prior	No.	§ 63.9(g)	Additional Notifications When Using CMS	Notification of performance evaluation. Notification using COMS data. Notification that exceeded criterion for relative accuracy	Yes. However, there are no opacity standards.	§ 63.9(h)(1)-(6)	Notification of Compliance Status	Contents. Due 60 days after end of performance test or other initial compliance demonstration, except for opacity/VE, which are due 30 days after. When to submit to Federal vs. State authority	Yes.	§ 63.9(i)	Adjustment of Submittal Deadlines	Procedures for Administrator to approve change in when notifications must be submitted	Yes.	§ 63.9(j)	Change in Previous Information	Must submit within 15 days after the change	Yes.	§ 63.9(k)	Electronic reporting procedures	Electronic reporting procedures for notifications per § 63.9(j)	Yes.	§ 63.10(a)	Recordkeeping/Reporting	Applies to all, unless compliance extension. When to submit to Federal vs. State authority. Procedures for owners of more than 1 source	Yes.	§ 63.10(b)(1)	Recordkeeping/Reporting	General Requirements. Keep all records readily available. Keep for 5 years	Yes.	§ 63.10(b)(2)(i) and (ii)	Records related to SSM	Exceedance of emission limit during startup, shutdown or malfunction	No, for new sources for which initial startup is after September 3, 2019. Yes, for all other affected sources before January 7, 2021, and No thereafter.	§ 63.10(b)(2)(iii)	Maintenance Records	Maintenance on air pollution control equipment.	Yes.	§ 63.10(b)(2)(iv) and (v)	Records related to SSM	Actions during SSM.	No, for new sources for which initial startup is after September 3, 2019. Yes, for all other affected sources before January 7, 2021, and No thereafter.	§ 63.10(b)(2)(vi) and (x-xi)	CMS Records	Malfunctions, inoperative, out-of-control. Calibration checks. Adjustments, maintenance	Yes.	§ 63.10(b)(2)(vii)-(ix)	Records	Measurements to demonstrate compliance with emissions limitations. Performance test, performance evaluation, and visible emissions observation results. Measurements to determine conditions of performance tests and performance evaluations	Yes.	§ 63.10(b)(2)(xii)	Records	Records when under waiver	Yes.	§ 63.10(b)(2)(xiii)	Records	Records when using alternative to relative accuracy test	No.	§ 63.10(b)(2)(xiv)	Records	All documentation supporting Initial Notification and Notification of Compliance Status	Yes.	§ 63.10(b)(3)	Records	Applicability Determinations	Yes.	§ 63.10(c)	Records	Additional Records for CMS	No.	§ 63.10(d)(1)	General Reporting Requirements	Requirement to report	Yes.	§ 63.10(d)(2)	Report of Performance Test Results	When to submit to Federal or State authority	Yes.	§ 63.10(d)(3)	Reporting Opacity or VE Observations	What to report and when	No.	§ 63.10(d)(4)	Progress Reports	Must submit progress reports on schedule if under compliance extension	Yes.	§ 63.10(d)(5)	Startup, Shutdown, and Malfunction Reports	Contents and submission	No, see § 63.7951(b)(4).	§ 63.10(e)(1)-(2)	Additional CMS Reports	Must report results for each CEM on a unit Written copy of performance evaluation Three copies of COMS performance evaluation	Yes. However, COMS are not applicable.	§ 63.10(e)(3)	Reports	Excess Emissions Reports	No.	§ 63.10(e)(3)(i-iii)	Reports	Schedule for reporting excess emissions and parameter monitor exceedance (now defined as deviations)	No.	§ 63.10(e)(3)(iv-v)	Excess Emissions Reports	Requirement to revert to quarterly submission if there is an excess emissions and parameter monitor exceedance (now defined as deviations). Provision to request semiannual reporting after compliance for one year. Submit report by 30th day following end of quarter or calendar half. If there has not been an exceedance or excess emissions (now defined as deviations), report contents is a statement that there have been no deviations	No.	§ 63.10(e)(3)(iv-v)	Excess Emissions Reports	Must submit report containing all of the information in §§ 63.10(c)(5-13) and 63.8(c)(7-8)	No.	§ 63.10(e)(3)(vi-viii)	Excess Emissions Report and Summary Report	Requirements for reporting excess emissions for CMSs (now called deviations). Requires all of the information in §§ 63.10(c)(5-13) and 63.8(c)(7-8)	No.	§ 63.10(e)(4)	Reporting COMS data	Must submit COMS data with performance test data	No.	§ 63.10(f)	Waiver for Recordkeeping/Reporting	Procedures for Administrator to waive	Yes.	§ 63.11	Control and work practice requirements	Requirements for flares and alternative work practice for equipment leaks	Yes.	§ 63.12	Delegation	State authority to enforce standards	Yes.	§ 63.13	Addresses	Addresses where reports, notifications, and requests are sent	Yes, only applicable to those reports not required to be submitted electronically.	§ 63.14	Incorporation by Reference	Test methods incorporated by reference	Yes.	§ 63.15	Availability of Information	Public and confidential information	Yes.

[85 FR 41712, July 10, 2020, as amended at 85 FR 73913, Nov. 19, 2020]