- Table 5 to Subpart WWWW of Part 63—Alternative Organic HAP Emissions Limits for Open Molding, Centrifugal Casting, and SMC Manufacturing Operations Where the Standards Are Based on a 95 Percent Reduction Requirement
As specified in § 63.5805, as an alternative to the 95 percent organic HAP emissions reductions requirement, you may meet the appropriate organic HAP emissions limits in the following table:
| If your operation type is . . . | And you use . . . | LYour organic HAP emissions limit is a 1. . . | 1. Open molding—corrosion-resistant and/or high strength (CR/HS) | a. Mechanical resin application | 6 lb/ton. | b. Filament application | 9 lb/ton. | c. Manual resin application | 7 lb/ton. | 2. Open molding—non-CR/HS | a. mechanical resin application | 13 lb/ton. | b. Filament application | 10 lb/ton. | c. Manual resin application | 5 lb/ton. | 3. Open molding—tooling | a. Mechanical resin application | 13 lb/ton. | b. Manual resin application | 8 lb/ton. | 4. Open molding—low flame spread/low smoke products | a. Mechanical resin application | 25 lb/ton. | b. Filament application | 14 lb/ton. | c. Manual resin application | 12 lb/ton. | 5. Open molding—shrinkage controlled resins | a. Mechanical resin application | 18 lb/ton. | b. Filament application | 11 lb/ton. | c. Manual resin application | 9 lb/ton. | 6. Open molding—gel coat 2 | a. Tooling gel coating | 22 lb/ton. | b. White/off white pigmented gel coating | 22 lb/ton. | c. All other pigmented gel coating | 19 lb/ton. | d. CR/HS or high performance gel coat | 31 lb/ton. | e. Fire retardant gel coat | 43 lb/ton. | f. Clear production gel coat | 27 lb/ton. | 7. Centrifugal casting—CR/HS 3 4 | A vent system that moves heated air through the mold | 27 lb/ton. | 8. Centrifugal casting—non-CR/HS 3 4 | A vent system that moves heated air through the mold | 21 lb/ton. | 7. Centrifugal casting—CR/HS 3 4 | A vent system that moves ambient air through the mold | 2 lb/ton. | 8. Centrifugal casting—non-CR/HS 3 4 | A vent system that moves ambient air through the mold | 1 lb/ton. | 9. SMC Manufacturing | N/A | 2.4 lb/ton. |
|---|
1 Organic HAP emissions limits for open molding and centrifugal casting expressed as lb/ton are calculated using the equations shown in Table 1 to this subpart. You must be at or below these values based on a 12-month rolling average.
2 These limits are for spray application of gel coat. Manual gel coat application must be included as part of spray gel coat application for compliance purposes using the same organic HAP emissions factor equation and organic HAP emissions limit. If you only apply gel coat with manual application, treat the manually applied gel coat as if it were applied with atomized spray for compliance determinations.
3 Centrifugal casting operations where the mold is not vented during spinning and cure are considered to be closed molding and are not subject to any emissions limit. Centrifugal casting operations where the mold is not vented during spinning and cure, and the resin is applied to the open centrifugal casting mold using mechanical or manual open molding resin application techniques are considered to be open molding operations and the appropriate open molding emission limits apply.
4 Centrifugal casting operations where the mold is vented during spinning and the resin is applied to the open centrifugal casting mold using mechanical or manual open molding resin application techniques, use the appropriate centrifugal casting emission limit to determine compliance. Calculate your emission factor using the appropriate centrifugal casting emission factor in Table 1 to this subpart, or a site specific emission factor as discussed in § 63.5796.