Collapse to view only § 129.101 - Purpose and definition.
- § 129.101 - Purpose and definition.
- § 129.103 - [Reserved]
- § 129.105 - Aging airplane inspections and records reviews for U.S.-registered multiengine aircraft.
- § 129.107 - Repairs assessment for pressurized fuselages.
- § 129.109 - Supplemental inspections for U.S.-registered aircraft.
- § 129.111 - Electrical wiring interconnection systems (EWIS) maintenance program.
- § 129.113 - Fuel tank system maintenance program.
- § 129.115 - Limit of validity.
- § 129.117 - Flammability reduction means.
- § 129.119 - Fuel tank vent explosion protection.
§ 129.101 - Purpose and definition.
(a) This subpart requires a foreign person or foreign air carrier operating a U.S. registered airplane in common carriage to support the continued airworthiness of each airplane. These requirements may include, but are not limited to, revising the maintenance program, incorporating design changes, and incorporating revisions to Instructions for Continued Airworthiness.
(b) [Reserved]
§ 129.103 - [Reserved]
§ 129.105 - Aging airplane inspections and records reviews for U.S.-registered multiengine aircraft.
(a) Operation after inspection and records review. After the dates specified in this paragraph, a foreign air carrier or foreign person may not operate a U.S.-registered multiengine airplane under this part unless the Administrator has notified the foreign air carrier or foreign person that the Administrator has completed the aging airplane inspection and records review required by this section. During the inspection and records review, the foreign air carrier or foreign person must demonstrate to the Administrator that the maintenance of age sensitive parts and components of the airplane has been adequate and timely enough to ensure the highest degree of safety.
(1) Airplanes exceeding 24 years in service on December 8, 2003; initial and repetitive inspections and records reviews. For an airplane that has exceeded 24 years in service on December 8, 2003, no later than December 5, 2007, and thereafter at intervals not to exceed 7 years.
(2) Airplanes exceeding 14 years in service but not 24 years in service on December 8, 2003; initial and repetitive inspections and records reviews. For an airplane that has exceeded 14 years in service, but not 24 years in service, on December 8, 2003, no later than December 4, 2008, and thereafter at intervals not to exceed 7 years.
(3) Airplanes not exceeding 14 years in service on December 8, 2003; initial and repetitive inspections and records reviews. For an airplane that has not exceeded 14 years in service on December 8, 2003, no later than 5 years after the start of the airplane's 15th year in service and thereafter at intervals not to exceed 7 years.
(b) Unforeseen schedule conflict. In the event of an unforeseen scheduling conflict for a specific airplane, the Administrator may approve an extension of up to 90 days beyond an interval specified in paragraph (b) of this section.
(c) Airplane and records availability. The foreign air carrier or foreign person must make available to the Administrator each U.S.-registered multiengine airplane for which an inspection and records review is required under this section, in a condition for inspection specified by the Administrator, together with the records containing the following information:
(1) Total years in service of the airplane;
(2) Total time in service of the airframe;
(3) Total flight cycles of the airframe;
(4) Date of the last inspection and records review required by this section;
(5) Current status of life-limited parts of the airframe;
(6) Time since the last overhaul of all structural components required to be overhauled on a specific time basis;
(7) Current inspection status of the airplane, including the time since the last inspection required by the inspection program under which the airplane is maintained;
(8) Current status of applicable airworthiness directives, including the date and methods of compliance, and if the airworthiness directive involves recurring action, the time and date when the next action is required;
(9) A list of major structural alterations; and
(10) A report of major structural repairs and the current inspection status for those repairs.
(d) Notification to Administrator. Each foreign air carrier or foreign person must notify the Administrator at least 60 days before the date on which the airplane and airplane records will be made available for the inspection and records review.
§ 129.107 - Repairs assessment for pressurized fuselages.
(a) No foreign air carrier or foreign persons operating a U.S. registered airplane may operate an Airbus Model A300 (excluding −600 series), British Aerospace Model BAC 1-11, Boeing Model 707, 720, 727, 737, or 747, McDonnell Douglas Model DC-8, DC-9/MD-80 or DC-10, Fokker Model F28, or Lockheed Model L-1011 beyond the applicable flight cycle implementation time specified below, or May 25, 2001, whichever occurs later, unless operations specifications have been issued to reference repair assessment guidelines applicable to the fuselage pressure boundary (fuselage skin, door skin, and bulkhead webs), and those guidelines are incorporated in its maintenance program. The repair assessment guidelines must be approved by the responsible Aircraft Certification Service office for the type certificate for the affected airplane.
(1) For the Airbus Model A300 (excluding the -600 series), the flight cycle implementation time is:
(i) Model B2: 36,000 flights.
(ii) Model B4-100 (including Model B4-2C): 30,000 flights above the window line, and 36,000 flights below the window line.
(iii) Model B4-200: 25,500 flights above the window line, and 34,000 flights below the window line.
(2) For all models of the British Aerospace BAC 1-11, the flight cycle implementation time is 60,000 flights.
(3) For all models of the Boeing 707, the flight cycle implementation time is 15,000 flights.
(4) For all models of the Boeing 720, the flight cycle implementation time is 23,000 flights.
(5) For all models of the Boeing 727, the flight cycle implementation time is 45,000 flights.
(6) For all models of the Boeing 737, the flight cycle implementation time is 60,00 flights.
(7) For all models of the Boeing 747, the flight cycle implementation time is 15,000 flights.
(8) For all models of the McDonnell Douglas DC-8, the flight cycle implementation time is 30,000 flights.
(9) For all models of the McDonnell Douglas DC-9/MD-80, the flight cycle implementation time is 60,000 flights.
(10) For all models of the McDonnell Douglas DC-10, the flight cycle implementation time is 30,000 flights.
(11) For all models of the Lockheed L-1011, the flight cycle implementation time is 27,000 flights.
(12) For the Fokker F-28 Mark 1000, 2000, 3000, and 4000, the flight cycle implementation time is 60,000 flights.
(b) [Reserved]
§ 129.109 - Supplemental inspections for U.S.-registered aircraft.
(a) Applicability. This section applies to U.S.-registered, transport category, turbine powered airplanes with a type certificate issued after January 1, 1958 that as a result of original type certification or later increase in capacity have—
(1) A maximum type certificated passenger seating capacity of 30 or more; or
(2) A maximum payload capacity of 7,500 pounds or more.
(b) General requirements. After December 20, 2010, a certificate holder may not operate an airplane under this part unless the following requirements have been met:
(1) Baseline Structure. The certificate holder's maintenance program for the airplane includes FAA-approved damage-tolerance-based inspections and procedures for airplane structure susceptible to fatigue cracking that could contribute to a catastrophic failure. For the purpose of this section, this structure is termed “fatigue critical structure.”
(2) Adverse effects of repairs, alterations, and modifications. The maintenance program for the airplane includes a means for addressing the adverse effects repairs, alterations, and modifications may have on fatigue critical structure and on inspections required by paragraph (b)(1) of this section. The means for addressing these adverse effects must be approved by the responsible Aircraft Certification Service office.
(3) Changes to maintenance program. The changes made to the maintenance program required by paragraph (b)(1) and (b)(2) of this section, and any later revisions to these changes, must be submitted to the Principal Maintenance Inspector for review and approval.
§ 129.111 - Electrical wiring interconnection systems (EWIS) maintenance program.
(a) Except as provided in paragraph (f) of this section, this section applies to transport category, turbine-powered airplanes with a type certificate issued after January 1, 1958, that, as a result of original type certification or later increase in capacity, have—
(1) A maximum type-certificated passenger capacity of 30 or more, or
(2) A maximum payload capacity of 7500 pounds or more.
(b) After March 10, 2011, no foreign person or foreign air carrier may operate a U.S.-registered airplane identified in paragraph (a) of this section unless the maintenance program for that airplane includes inspections and procedures for EWIS.
(c) The proposed EWIS maintenance program changes must be based on EWIS Instructions for Continued Airworthiness (ICA) that have been developed in accordance with the provisions of Appendix H of part 25 of this chapter applicable to each affected airplane (including those ICA developed for supplemental type certificates installed on each airplane) and that have been approved by the responsible Aircraft Certification Service office.
(1) For airplanes subject to § 26.11 of this chapter, the EWIS ICA must comply with paragraphs H25.5(a)(1) and (b).
(2) For airplanes subject to § 25.1729 of this chapter, the EWIS ICA must comply with paragraph H25.4 and all of paragraph H25.5.
(d) After March 10, 2011, before returning a U.S.-registered airplane to service after any alterations for which EWIS ICA are developed, the foreign person or foreign air carrier must include in the maintenance program for that airplane inspections and procedures for EWIS based on those ICA.
(e) The EWIS maintenance program changes identified in paragraphs (c) and (d) of this section and any later EWIS revisions must be submitted to the Principal Inspector or Flight Standards office responsible for review and approval.
(f) This section does not apply to the following airplane models:
(1) Lockheed L-188
(2) Bombardier CL-44
(3) Mitsubishi YS-11
(4) British Aerospace BAC 1-11
(5) Concorde
(6) deHavilland D.H. 106 Comet 4C
(7) VFW-Vereinigte Flugtechnische Werk VFW-614
(8) Illyushin Aviation IL 96T
(9) Bristol Aircraft Britannia 305
(10) Handley Page Herald Type 300
(11) Avions Marcel Dassault—Breguet Aviation Mercure 100C
(12) Airbus Caravelle
(13) Lockheed L-300
§ 129.113 - Fuel tank system maintenance program.
(a) Except as provided in paragraph (g) of this section, this section applies to transport category, turbine-powered airplanes with a type certificate issued after January 1, 1958, that, as a result of original type certification or later increase in capacity, have—
(1) A maximum type-certificated passenger capacity of 30 or more, or
(2) A maximum payload capacity of 7500 pounds or more.
(b) For each U.S.-registered airplane on which an auxiliary fuel tank is installed under a field approval, before June 16, 2008, the foreign person or foreign air carrier operating the airplane must submit to the responsible Aircraft Certification Service office proposed maintenance instructions for the tank that meet the requirements of Special Federal Aviation Regulation No. 88 (SFAR 88) of this chapter.
(c) After December 16, 2008, no foreign person or foreign air carrier may operate a U.S.-registered airplane identified in paragraph (a) of this section unless the maintenance program for that airplane has been revised to include applicable inspections, procedures, and limitations for fuel tank systems.
(d) The proposed fuel tank system maintenance program revisions must be based on fuel tank system Instructions for Continued Airworthiness (ICA) that have been developed in accordance with the applicable provisions of SFAR 88 of this chapter or § 25.1529 and part 25, Appendix H, of this chapter, in effect on June 6, 2001 (including those developed for auxiliary fuel tanks, if any, installed under supplemental type certificates or other design approval) and that have been approved by the responsible Aircraft Certification Service office.
(e) After December 16, 2008, before returning a U.S.-registered airplane to service after any alteration for which fuel tank ICA are developed under SFAR 88, or under § 25.1529 in effect on June 6, 2001, the foreign person or foreign air carrier must include in the maintenance program for the airplane inspections and procedures for the fuel tank system based on those ICA.
(f) The fuel tank system maintenance program changes identified in paragraphs (d) and (e) of this section and any later fuel tank system revisions must be submitted to the Principal Inspector or Flight Standards office responsible for review and approval.
(g) This section does not apply to the following airplane models:
(1) Bombardier CL-44
(2) Concorde
(3) deHavilland D.H. 106 Comet 4C
(4) VFW-Vereinigte Flugtechnische Werk VFW-614
(5) Illyushin Aviation IL 96T
(6) Bristol Aircraft Britannia 305
(7) Handley Page Herald Type 300
(8) Avions Marcel Dassault—Breguet Aviation Mercure 100C
(9) Airbus Caravelle
(10) Lockheed L-300
§ 129.115 - Limit of validity.
(a) Applicability. This section applies to foreign air carriers or foreign persons operating any U.S.-registered transport category, turbine-powered airplane with a maximum takeoff gross weight greater than 75,000 pounds and a type certificate issued after January 1, 1958, regardless of whether the maximum takeoff gross weight is a result of an original type certificate or a later design change. This section also applies to foreign air carriers or foreign persons operating any other U.S.-registered transport category, turbine-powered airplane with a type certificate issued after January 1, 1958, regardless of the maximum takeoff gross weight, for which a limit of validity of the engineering data that supports the structural maintenance program (hereafter referred to as LOV) is required in accordance with § 25.571 or § 26.21 of this chapter after January 14, 2011.
(b) Limit of validity. No foreign air carrier or foreign person may operate a U.S.-registered airplane identified in paragraph (a) of this section after the applicable date identified in Table 1 of this section, unless an Airworthiness Limitations section (ALS) approved under Appendix H to part 25 or § 26.21 of this chapter is incorporated into its maintenance program. The ALS must—
(1) Include an LOV approved under § 25.571 or § 26.21 of this chapter, as applicable, except as provided in paragraph (f) of this section; and
(2) Be clearly distinguishable within its maintenance program.
(c) Operation of airplanes excluded from § 26.21. No certificate holder may operate an airplane identified in § 26.21(g) of this chapter after July 14, 2013, unless an ALS approved under Appendix H to part 25 or § 26.21 of this chapter is incorporated into its maintenance program. The ALS must—
(1) Include an LOV approved under § 25.571 or § 26.21 of this chapter, as applicable, except as provided in paragraph (f) of this section; and
(2) Be clearly distinguishable within its maintenance program
(d) Extended limit of validity. No foreign air carrier or foreign person may operate an airplane beyond the LOV or extended LOV specified in paragraph (b)(1), (c), (d), or (f) of this section, as applicable, unless the following conditions are met:
(1) An ALS must be incorporated into its maintenance program that—
(i) Includes an extended LOV and any widespread fatigue damage airworthiness limitation items (ALIs) approved under § 26.23 of this chapter; and
(ii) Is approved under § 26.23 of this chapter;
(2) The extended LOV and the airworthiness limitation items pertaining to widespread fatigue damage must be clearly distinguishable within its maintenance program.
(e) Principal Maintenance Inspector approval. Foreign air carriers or foreign persons must submit the maintenance program revisions required by paragraphs (b), (c), and (d) of this section to the Principal Maintenance Inspector or Flight Standards office for review and approval.
(f) Exception. For any airplane for which an LOV has not been approved as of the applicable compliance date specified in paragraph (c) or Table 1 of this section, instead of including an approved LOV in the ALS, an operator must include the applicable default LOV specified in Table 1 or Table 2 of this section, as applicable, in the ALS.
Table 1—Airplanes Subject to § 26.21
| Airplane model | Compliance Date—months after
January 14, 2011 | Default LOV
[flight cycles (FC) or flight hours (FH)] | Airbus—Existing 1 Models Only: | A300 B2-1A, B2-1C, B2K-3C, B2-203 | 30 | 48,000 FC | A300 B4-2C, B4-103 | 30 | 40,000 FC | A300 B4-203 | 30 | 34,000 FC | A300-600 Series | 60 | 30,000 FC/67,500 FH | A310-200 Series | 60 | 40,000 FC/60,000 FH | A310-300 Series | 60 | 35,000 FC/60,000 FH | A318 Series | 60 | 48,000 FC/60,000 FH | A319 Series | 60 | 48,000 FC/60,000 FH | A320-100 Series | 60 | 48,000 FC/48,000 FH | A320-200 Series | 60 | 48,000 FC/60,000 FH | A321 Series | 60 | 48,000 FC/60,000 FH | A330-200, -300 Series (except WV050 family) (non enhanced) | 60 | 40,000 FC/60,000 FH | A330-200, -300 Series WV050 family (enhanced) | 60 | 33,000 FC/100,000 FH | A330-200 Freighter Series | 60 | See span. | A340-200, -300 Series (except WV 027 and WV050 family) (non enhanced) | 60 | 20,000 FC/80,000 FH | A340-200, -300 Series WV 027 (non enhanced) | 60 | 30,000 FC/60,000 FH | A340-300 Series WV050 family (enhanced) | 60 | 20,000 FC/100,000 FH | A340-500, -600 Series | 60 | 16,600 FC/100,000 FH | A380-800 Series | 72 | See span. | Boeing—Existing 1 Models Only: | 717 | 60 | 60,000 FC/60,000 FH | 727 (all series) | 30 | 60,000 FC | 737 (Classics): 737-100, -200, -200C, -300, -400, -500 | 30 | 75,000 FC | 737 (NG): 737-600, -700, -700C, -800, -900, -900ER | 60 | 75,000 FC | 747 (Classics): 747-100, -100B, -100B SUD, -200B, -200C, -200F, -300, 747SP, 747SR | 30 | 20,000 FC | 747-400: 747-400, -400D, -400F | 60 | 20,000 FC | 757 | 60 | 50,000 FC | 767 | 60 | 50,000 FC | 777-200, -300 | 60 | 40,000 FC | 777-200LR, 777-300ER | 72 | 40,000 FC | 777F | 72 | 11,000 FC | Bombardier—Existing 1 Models Only: | CL-600: 2D15 (Regional Jet Series 705), 2D24 (Regional Jet Series 900) | 72 | 60,000 FC | Embraer—Existing 1 Models Only: | ERJ 170 | 72 | See span. | ERJ 190 | 72 | See span. | Fokker—Existing 1 Models Only: | F.28 Mark 0070, Mark 0100 | 30 | 90,000 FC | Lockheed—Existing 1 Models Only: | L-1011 | 30 | 36,000 FC | 188 | 30 | 26,600 FC | 382 (all series) | 30 | 20,000 FC/50,000 FH | McDonnell Douglas—Existing 1 Models Only: | DC-8, -8F | 30 | 50,000 FC/50,000 FH | DC-9 (except for MD-80 models) | 30 | 100,000 FC/100,000 FH | MD-80 (DC-9-81, -82, -83, -87, MD-88) | 30 | 50,000 FC/50,000 FH | MD-90 | 60 | 60,000 FC/90,000 FH | DC-10-10, -15 | 30 | 42,000 FC/60,000 FH | DC-10-30, -40, -10F, -30F, -40F | 30 | 30,000 FC/60,000 FH | MD-10-10F | 60 | 42,000 FC/60,000 FH | MD-10-30F | 60 | 30,000 FC/60,000 FH | MD-11, MD-11F | 60 | 20,000 FC/60,000 FH | Maximum Takeoff Gross Weight Changes: | All airplanes whose maximum takeoff gross weight has been decreased to 75,000 pounds or below after January 14, 2011, or increased to greater than 75,000 pounds at any time by an amended type certificate or supplemental type certificate | 30, or within 12 months after the LOV is approved, or before operating the airplane, whichever occurs latest | Not applicable. | All Other Airplane Models (TCs and amended TCs) not Listed in Table 2 | 72, or within 12 months after the LOV is approved, or before operating the airplane, whichever occurs latest | Not applicable. |
|---|
1 Type certificated as of January 14, 2011.
Airplane operation limitation is stated in the Airworthiness Limitation section.
Table 2—Airplanes Excluded From § 26.21
| Airplane model | Default LOV [flight cycles (FC) or flight hours (FH)] | Airbus: | Caravelle | 15,000 FC/24,000 FH | Avions Marcel Dassault: | Breguet Aviation Mercure 100C | 20,000 FC/16,000 FH | Boeing: | Boeing 707 (-100 Series and -200 Series) | 20,000 FC | Boeing 707 (-300 Series and -400 Series) | 20,000 FC | Boeing 720 | 30,000 FC | Bombardier: | CL-44D4 and CL-44J | 20,000 FC | BD-700 | 15,000 FC | Bristol Aeroplane Company: | Britannia 305 | 10,000 FC | British Aerospace Airbus, Ltd.: | BAC 1-11 (all models) | 85,000 FC | British Aerospace (Commercial Aircraft) Ltd.: | Armstrong Whitworth Argosy A.W. 650 Series 101 | 20,000 FC | BAE Systems (Operations) Ltd.: | BAe 146-100A (all models) | 50,000 FC | BAe 146-200-07 | 50,000 FC | BAe 146-200-07 Dev | 50,000 FC | BAe 146-200-11 | 50,000 FC | BAe 146-200-07A | 47,000 FC | BAe 146-200-11 Dev | 43,000 FC | BAe 146-300 (all models) | 40,000 FC | Avro 146-RJ70A (all models) | 40,000 FC | Avro 146-RJ85A and 146-RJ100A (all models) | 50,000 FC | D & R Nevada, LLC: | Convair Model 22 | 1,000 FC/1,000 FH | Convair Model 23M | 1,000 FC/1,000 FH | deHavilland Aircraft Company, Ltd.: | D.H. 106 Comet 4C | 8,000 FH | Gulfstream: | GV | 40,000 FH | GV-SP | 40,000 FH | Ilyushin Aviation Complex: | IL-96T | 10,000 FC/30,000 FH | Lockheed: | 300-50A01 (USAF C 141A) | 20,000 FC |
|---|
§ 129.117 - Flammability reduction means.
(a) Applicability. Except as provided in paragraph (o) of this section, this section applies to U.S.-registered transport category, turbine-powered airplanes with a type certificate issued after January 1, 1958, that as a result of original type certification or later increase in capacity have:
(1) A maximum type-certificated passenger capacity of 30 or more, or
(2) A maximum payload capacity of 7,500 pounds or more.
(b) New Production Airplanes. Except in accordance with § 129.14, no foreign air carrier or foreign person may operate an airplane identified in Table 1 of this section (including all-cargo airplanes) for which application is made for original certificate of airworthiness or export airworthiness approval after December 27, 2010 unless an Ignition Mitigation Means (IMM) or Flammability Reduction Means (FRM) meeting the requirements of § 26.33 of this chapter is operational.
Table 1
| Model—Boeing | Model—Airbus | 747 Series | A318, A319, A320, A321 Series | 737 Series | A330, A340 Series | 777 Series | 767 Series |
|---|
(c) Auxiliary Fuel Tanks. After the applicable date stated in paragraph (e) of this section, no foreign air carrier or foreign person may operate any airplane subject § 26.33 of this chapter that has an Auxiliary Fuel Tank installed pursuant to a field approval, unless the following requirements are met:
(1) The foreign air carrier or foreign person complies with 14 CFR 26.35 by the applicable date stated in that section.
(2) The foreign air carrier or foreign person installs Flammability Impact Mitigation Means (FIMM), if applicable, that are approved by the responsible Aircraft Certification Service office.
(3) Except in accordance with § 129.14, the FIMM, if applicable, are operational.
(d) Retrofit. After the dates specified in paragraph (e) of this section, no foreign air carrier or foreign person may operate an airplane to which this section applies unless the requirements of paragraphs (d)(1) and (d)(2) of this section are met.
(1) IMM, FRM or FIMM, if required by §§ 26.33, 26.35, or 26.37 of this chapter, that are approved by the responsible Aircraft Certification Service office, are installed within the compliance times specified in paragraph (e) of this section.
(2) Except in accordance with § 129.14, the IMM, FRM or FIMM, as applicable, are operational.
(e) Compliance Times. Except as provided in paragraphs (k) and (l) of this section, the installations required by paragraph (d) of this section must be accomplished no later than the applicable dates specified in paragraph (e)(1) or (e)(2) of this section.
(1) Fifty percent of each foreign air carrier or foreign person's fleet identified in paragraph (d)(1) of this section must be modified no later than December 26, 2014.
(2) One hundred percent of each foreign air carrier or foreign person's fleet of airplanes subject to paragraph (d)(1) or this section must be modified no later than December 26, 2017.
(3) For those foreign air carriers or foreign persons that have only one airplane for a model identified in Table 1, the airplane must be modified no later than December 26, 2017.
(f) Compliance after Installation. Except in accordance with § 129.14, no person may—
(1) Operate an airplane on which IMM or FRM has been installed before the dates specified in paragraph (e) of this section unless the IMM or FRM is operational.
(2) Deactivate or remove an IMM or FRM once installed unless it is replaced by a means that complies with paragraph (d) of this section.
(g) Maintenance Program Revisions. No foreign air carrier or foreign person may operate an airplane for which airworthiness limitations have been approved by the responsible Aircraft Certification Service office in accordance with §§ 26.33, 26.35, or 26.37 of this chapter after the airplane is modified in accordance with paragraph (d) of this section unless the maintenance program for that airplane is revised to include those applicable airworthiness limitations.
(h) After the maintenance program is revised as required by paragraph (g) of this section, before returning an airplane to service after any alteration for which airworthiness limitations are required by §§ 25.981, 26.33, 26.35, or 26.37 of this chapter, the foreign person or foreign air carrier must revise the maintenance program for the airplane to include those airworthiness limitations.
(i) The maintenance program changes identified in paragraphs (g) and (h) of this section must be submitted to the operator's responsible Flight Standards office or Principal Inspector for review and approval prior to incorporation.
(j) The requirements of paragraph (d) of this section do not apply to airplanes operated in all-cargo service, but those airplanes are subject to paragraph (f) of this section.
(k) The compliance dates specified in paragraph (e) of this section may be extended by one year, provided that—
(1) No later than March 26, 2009, the foreign air carrier or foreign person notifies its responsible Flight Standards office or Principal Inspector that it intends to comply with this paragraph;
(2) No later than June 24, 2009, the foreign air carrier or foreign person applies for an amendment to its operations specifications in accordance with § 129.11 to include a requirement for the airplane models specified in Table 2 of this section to use ground air conditioning systems for actual gate times of more than 30 minutes, when available at the gate and operational, whenever the ambient temperature exceeds 60 degrees Fahrenheit; and
(3) Thereafter, the certificate holder uses ground air conditioning systems as described in paragraph (k)(2) of this section on each airplane subject to the extension.
Table 2
| Model—Boeing | Model—Airbus | 747 Series | A318, A319, A320, A321 Series | 737 Series | A300, A310 Series | 777 Series | A330, A340 Series | 767 Series | 757 Series |
|---|
(l) For any foreign air carrier or foreign person for which the operating certificate is issued after December 26, 2008, the compliance date specified in paragraph (e) of this section may be extended by one year, provided that the foreign air carrier or foreign person meets the requirements of paragraph (k)(2) of this section when its initial operations specifications are issued and, thereafter, uses ground air conditioning systems as described in paragraph (k)(2) of this section on each airplane subject to the extension.
(m) After the date by which any person is required by this section to modify 100 percent of the affected fleet, no person may operate in passenger service any airplane model specified in Table 2 of this section unless the airplane has been modified to comply with § 26.33(c) of this chapter.
Table 3
| Model—Boeing | Model—Airbus | 747 Series | A318, A319, A320, A321 Series | 737 Series | A300, A310 Series | 777 Series | A330, A340 Series | 767 Series | 757 Series |
|---|
(n) No foreign air carrier or foreign person may operate any airplane on which an auxiliary fuel tank is installed after December 26, 2017 unless the FAA has certified the tank as compliant with § 25.981 of this chapter, in effect on December 26, 2008.
(o) Exclusions. The requirements of this section do not apply to the following airplane models:
(1) Convair CV-240, 340, 440, including turbine powered conversions.
(2) Lockheed L-188 Electra.
(3) Vickers VC-10.
(4) Douglas DC-3, including turbine powered conversions.
(5) Bombardier CL-44.
(6) Mitsubishi YS-11.
(7) BAC 1-11.
(8) Concorde.
(9) deHavilland D.H. 106 Comet 4C.
(10) VFW—Vereinigte Flugtechnische VFW-614.
(11) Illyushin Aviation IL 96T.
(12) Bristol Aircraft Britannia 305.
(13) Handley Page Herald Type 300.
(14) Avions Marcel Dassault—Breguet Aviation Mercure 100C.
(15) Airbus Caravelle.
(16) Fokker F-27/Fairchild Hiller FH-227.
(17) Lockheed L-300.
§ 129.119 - Fuel tank vent explosion protection.
(a) Applicability. This section applies to transport category, turbine-powered airplanes with a type certificate issued after January 1, 1958, that have:
(1) A maximum type-certificated passenger capacity of 30 or more; or
(2) A maximum payload capacity of 7,500 pounds or more.
(b) New production airplanes. No certificate holder may operate an airplane for which the State of Manufacture issued the original certificate of airworthiness or export airworthiness approval after August 23, 2018 unless means, approved by the Administrator, to prevent fuel tank explosions caused by propagation of flames from outside the fuel tank vents into the fuel tank vapor spaces are installed and operational.