View all text of Subpart A [§ 82.1 - § 82.27]
§ 82.27 - Incorporation by reference.
(a)(1) Certain material is incorporated by reference into this subpart with the approval of the Director of the Federal Register under 5 U.S.C. 552(a) and 1 CFR part 51. All approved incorporation by reference (IBR) material is available for inspection at EPA and at the National Archives and Records Administration (NARA). Contact EPA at: U.S. EPA's Air and Radiation Docket; EPA West Building, Room 3334, 1301 Constitution Ave. NW, Washington, DC 20460, 202-566-1742. For information on the availability of this material at NARA, visit www.archives.gov/federal-register/cfr/ibr-locations or email [email protected].
(2) The IBR material may be obtained from the sources in the following paragraphs of this section or from one or more private resellers listed in this paragraph (a)(2). For material that is no longer commercially available, contact: U.S. EPA's Air and Radiation Docket; EPA West Building, Room 3334, 1301 Constitution Ave. NW, Washington, DC 20460; [email protected].
(i) Accuris Standards Store, 321 Inverness Drive, South Englewood, CO 80112; phone: (800) 332-6077; website: https://accuristech.com.
(ii) American National Standards Institute (ANSI), 25 West 43rd Street, Fourth Floor, New York, NY 10036-7417; phone: (212) 642-4980; email: [email protected]; website: www.ansi.org.
(iii) GlobalSpec, 257 Fuller Road, Suite NFE 1100, Albany, NY 12203-3621; phone: (800) 261-2052; website: https://standards.globalspec.com.
(iv) Nimonik Document Center, 401 Roland Way, Suite 224, Oakland, CA 94624; phone (650) 591-7600; email: [email protected]; website: www.document-center.com.
(b) American Society of Mechanical Engineers (ASME), Two Park Avenue, New York, NY 10016, phone: 800.843.2763, email: [email protected]; website: www.asme.org.
(1) ASME MFC-3M-2004, Measurement of Fluid Flow in Pipes Using Orifice, Nozzle, and Venturi, issued August 15, 2005; IBR approved for § 82.25(d).
(2) ASME MFC-4M-1986 (Reaffirmed 2016), Measurement of Gas Flow by Turbine Meters, reaffirmed 2016, IBR approved for § 82.25(d).
(3) ASME MFC-5M-1985 (Reaffirmed 1994), Measurement of Liquid Flow in Closed Conduits Using Transit-Time Ultrasonic Flow Meters, copyright 1985; IBR approved for § 82.25(d).
(4) ASME MFC-6M-1998, Measurement of Fluid Flow in Pipes Using Vortex Flowmeters, July 4, 1998; IBR approved for § 82.25(d).
(5) ASME MFC-7M-1987 (Reaffirmed 1992), Measurement of Gas Flow by Means of Critical Flow Venturi Nozzles, copyright 1987; IBR approved for § 82.25(d).
(6) ASME MFC-9M-1988 (Reaffirmed 2001), Measurement of Liquid Flow in Closed Conduits by Weighing Method, reaffirmed 2001; IBR approved for § 82.25(d).
(7) ASME MFC-11M-2006, Measurement of Fluid Flow by Means of Coriolis Mass Flowmeters, issued March 30, 2007; IBR approved for § 82.25(d).
(8) ASME MFC-14M-2003, Measurement of Fluid Flow Using Small Bore Precision Orifice Meters, issued April 17, 2003; IBR approved for § 82.25(d).
(c) ASTM International, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428; phone: 610.832.9500; email: [email protected]; website: www.astm.org/.
(1) ASTM D6348-03 Standard Test Method for Determination of Gaseous Compounds by Extractive Direct Interface Fourier Transform Infrared (FTIR) Spectroscopy, approved October 1, 2003, IBR approved for § 82.25(d).
(2) [Reserved]
(d) U.S. Environmental Protection Agency, 1200 Pennsylvania Avenue NW, Washington, DC 20460; phone: 202.272.0167; website: www.epa.gov.
(1) Approved Alternative Method 012: An Alternate Procedure for Stack Gas Volumetric Flow Rate Determination (Tracer Gas) (ALT-012), U.S. Environmental Protection Agency Emission Measurement Center, May 23, 1994, IBR approved for § 82.25(d).
(2) Emissions Inventory Improvement Program, Volume II: Chapter 16, Methods for Estimating Air Emissions from Chemical Manufacturing Facilities, August 2007, Final, IBR approved for § 82.25(c).
(3) Protocol for Equipment Leak Emission Estimates, EPA-453/R-95-017, November 1995 (EPA-453/R-95-017), IBR approved for § 82.25(c) and (d).
(4) Protocol for Measuring Destruction or Removal Efficiency (DRE) of Fluorinated Greenhouse Gas Abatement Equipment in Electronics Manufacturing, Version 1, EPA-430-R-10-003, March 2010 (EPA 430-R-10-003), IBR approved for § 82.25 (d).
(5) Tracer Gas Protocol for the Determination of Volumetric Flow Rate Through the Ring Pipe of the Xact Multi-Metals Monitoring System, also known as Other Test Method 24 (Tracer Gas Protocol), Eli Lilly and Company Tippecanoe Laboratories, September 2006, IBR approved for § 82.25(d).