Collapse to view only § 751.507 - Certification of compliance for the chlor-alkali industry.
- § 751.501 - General.
- § 751.503 - Definitions.
- § 751.505 - Manufacturing, processing, distribution in commerce and commercial use of chrysotile asbestos diaphragms in the chlor-alkali industry.
- § 751.507 - Certification of compliance for the chlor-alkali industry.
- § 751.509 - Other prohibitions and restrictions on the manufacturing, processing, distribution in commerce and commercial use of chrysotile asbestos.
- § 751.511 - Interim workplace controls of chrysotile asbestos exposures.
- § 751.513 - Disposal.
- § 751.515 - Recordkeeping.
§ 751.501 - General.
This subpart sets certain restrictions on the manufacture (including import), processing, distribution in commerce, and commercial use and disposal of chrysotile asbestos (CASRN 132207-32-0) to prevent unreasonable risk of injury to health in accordance with TSCA section 6(a), 15 U.S.C. 2605(a).
§ 751.503 - Definitions.
The definitions in subpart A of this part apply to this subpart unless otherwise specified in this section. In addition, the following definitions apply to this subpart:
Aftermarket automotive brakes and linings means any automotive friction brake articles sold in the secondary market as replacement parts (e.g., brake pads, linings and shoes) used in disc and drum brake systems on automobiles and trucks.
Article means a manufactured item:
(1) Which is formed to a specific shape or design during manufacture;
(2) Which has end use function(s) dependent in whole or in part upon its shape or design during end use; and
(3) Which has either no change of chemical composition during its end use or only those changes of composition which have no commercial purpose separate from that of the article, and that result from a chemical reaction that occurs upon end use of other chemical substances, mixtures, or articles; except that fluids and particles are not considered articles regardless of shape or design.
Authorized person means any person specifically authorized by the owner or operator to enter, and whose duties require the person to enter, a regulated area.
Chrysotile asbestos is the asbestiform variety of a hydrated magnesium silicate mineral, with relatively long and flexible crystalline fibers that are capable of being woven.
Disposal means to discard, throw away, or otherwise complete or terminate the useful life of chrysotile asbestos, including any chrysotile asbestos-containing products or articles.
Distribution in commerce has the same meaning as in section 3 of the Act, but the term does not include distribution of chrysotile asbestos waste solely for purposes of disposal in accordance with this Subpart.
Diaphragms means semipermeable diaphragms, which separate the anode from the cathode chemicals in the production of chlorine and sodium hydroxide (caustic soda).
Gasket means an article used to form a leakproof seal between fixed components.
Membrane technology means a chlor-alkali production technology that uses chlorine production cells in which the anode and the cathode are separated by an ion-exchange membrane that is designed to allow only sodium ions and some water to pass through it.
Nuclear material means any source material, special nuclear material, or byproduct material (as such terms are defined in the Atomic Energy Act of 1954, as amended, and regulations issued under such Act).
Oilfield brake blocks means the friction brake blocks component in drawworks used in the hoisting mechanism for oil well drilling rigs.
Other gaskets means gaskets other than sheet gaskets in chemical production, to include gaskets used in the exhaust systems of utility vehicles.
Other vehicle friction products means friction articles such as brakes and clutches, other than aftermarket automotive brakes and linings, installed on any vehicle, including on off-road vehicles, trains, planes, etc. Other vehicle friction products does not include articles used in the NASA Super Guppy Turbine aircraft, a specialty cargo plane used for the transportation of oversized equipment that is owned and operated by the National Aeronautics and Space Administration (NASA).
Owner or operator means any person who owns, leases, operates, controls, or supervises a workplace covered by this subpart.
Potentially exposed person means any person who may be occupationally exposed to a chemical substance or mixture in a workplace as a result of a condition of use of that chemical substance or mixture.
Processing has the same meaning as in section 3 of the Act, but the term does not include processing of chrysotile asbestos waste solely for purposes of disposal in accordance with this subpart.
Regulated area means an area established by the regulated entity to demarcate where airborne concentrations of a specific chemical substance exceed, or there is a reasonable possibility they may exceed, the ECEL.
Savannah River Site means the Department of Energy's nuclear waste management and related national defense operations at its Savannah River Site in Aiken, Barnwell and Allendale counties in South Carolina, including operations at H-Canyon, F and H Tank Farms, Defense Waste Processing Facility, Savannah River National Laboratory and any on-site facility managed by Savannah River Nuclear Solutions.
Sheet gaskets in chemical production means gaskets cut from sheeting, including asbestos-containing rubberized sheeting, that are used in facilities for extreme condition applications such as titanium dioxide manufacturing, or processing nuclear material.
§ 751.505 - Manufacturing, processing, distribution in commerce and commercial use of chrysotile asbestos diaphragms in the chlor-alkali industry.
(a) After May 28, 2024, all persons are prohibited from manufacture (including import) of chrysotile asbestos, including any chrysotile asbestos-containing products or articles, for diaphragms in the chlor-alkali industry.
(b) After May 28, 2029, all persons are prohibited from processing, distribution in commerce and commercial use of chrysotile asbestos, including any chrysotile asbestos-containing products or articles, for diaphragms in the chlor-alkali industry, except as provided in paragraphs (c) through (d) of this section.
(c) Any person who meets all of the criteria of this paragraph (c) may process, distribute in commerce and commercially use chrysotile asbestos, including any chrysotile asbestos-containing products or articles, for diaphragms in the chlor-alkali industry at no more than two facilities until May 25, 2032:
(1) On May 28, 2024, the person owns or operates more than one facility that uses chrysotile asbestos in chlor-alkali production;
(2) The person is converting more than one facility that the person owns or operates that as of May 28, 2024 uses chrysotile asbestos in chlor-alkali production from the use of chrysotile asbestos diaphragms to non-chrysotile asbestos membrane technology, and by May 28, 2029, the person has ceased all processing, distribution in commerce and commercial use of chrysotile asbestos at one (or more) facility undergoing or that has undergone conversion to non-chrysotile asbestos membrane technology; and
(3) The person certifies to EPA compliance with the provisions of this paragraph, in accordance with § 751.507.
(d) Any person who meets all of the criteria of this paragraph (d) may process, distribute in commerce and commercially use chrysotile asbestos, including any chrysotile asbestos-containing products or articles, for diaphragms in the chlor-alkali industry at not more than one facility until May 26, 2036:
(1) On May 28, 2024, the person owns or operates more than two facilities that use chrysotile asbestos in chlor-alkali production; and
(2) The person is converting more than two facilities that the person owns or operates that as of May 28, 2024 use chrysotile asbestos in chlor-alkali production from the use of chrysotile asbestos diaphragms to non-chrysotile asbestos membrane technology:
(i) By May 28, 2029, the person has ceased all processing, distribution in commerce and commercial use of chrysotile asbestos at one (or more) facility undergoing or that has undergone such conversion; and
(ii) By May 25, 2032 the person has ceased all processing, distribution in commerce and commercial use of chrysotile asbestos at two (or more) facilities undergoing or that have undergone conversion to non-chrysotile asbestos membrane technology; and
(3) The person certifies to EPA compliance with the provisions of this paragraph, in accordance with § 751.507.
§ 751.507 - Certification of compliance for the chlor-alkali industry.
(a) In addition to meeting the requirements of §§ 751.505(c), any person who processes, distributes in commerce or commercially uses chrysotile asbestos for diaphragms in the chlor-alkali industry between May 28, 2029 and May 25, 2032 must:
(1) Certify to EPA their compliance with all requirements of § 751.505(c); and
(2) Provide the following information to EPA to support their compliance with the requirements of § 751.505(c):
(i) Identification of the facility for which, by May 28, 2029, the person has ceased all processing, distribution in commerce and commercial use of chrysotile asbestos, pursuant to § 751.505(c)(2), including:
(A) facility name, location, and mailing address;
(B) name of facility manager or other contact, title, phone number and email address; and
(C) date the person ceased all processing, distribution in commerce and commercial use of chrysotile asbestos at the facility.
(ii) Identification of the facility or facilities (no more than two facilities) for which the person will after May 28, 2029, continue to process, distribute in commerce and commercially use chrysotile asbestos diaphragms while the facility or facilities are being converted to non-chrysotile asbestos membrane technology, pursuant to § 751.505(c), including for each facility:
(A) facility name, location, and mailing address; and
(B) name of facility manager or other contact, title, phone number and email address.
(b) In addition to meeting the requirements of paragraph (a) of this section and §§ 751.505(d), any person who processes, distributes in commerce or commercially uses chrysotile asbestos for diaphragms in the chlor-alkali industry between May 25, 2032 and May 26, 2036 must:
(1) Certify to EPA their compliance with all requirements of § 751.505(d); and
(2) Provide the following information to EPA to support their compliance with the requirements of § 751.505(d):
(i) Identification of the facility identified in § 751.505(d)(2)(ii) at which as of May 25, 2032, the person has ceased all processing, distribution in commerce and commercial use of chrysotile asbestos, including:
(A) facility name, location, and mailing address;
(B) name of facility manager or other contact, title, phone number and email address; and
(C) date the person has ceased all processing, distribution in commerce and commercial use of chrysotile asbestos at the facility.
(ii) Identification of the facility at which the person will between May 25, 2032 and no later than May 26, 2036, continue to process, distribute in commerce and commercially use chrysotile asbestos diaphragms while the facility is being converted to non-chrysotile asbestos membrane technology pursuant to § 751.505(d), including:
(A) facility name, location, and mailing address; and
(B) name of facility manager or other contact, title, phone number and email address.
(c) The certification required by paragraphs (a) and (b) of this section must be signed and dated by a responsible corporate officer. For the purpose of this section, a responsible corporate officer means: a president, secretary, treasurer, or vice-president of the corporation in charge of chlor-alkali operations, or any other person who performs similar policy or decision-making functions for the corporation.
(d) Any person signing a document under paragraph (c) of this section shall also make the following certification:
“I certify under penalty of law that this document was prepared under my direction or supervision, and the information is, to the best of my knowledge and belief, true, accurate, and complete. I am aware it is unlawful to knowingly submit incomplete, false and/or misleading information and there are criminal penalties for such conduct.”
(e) This certification must be submitted to the Director, Office of Pollution Prevention and Toxics (OPPT), using the address specified at 40 CFR 700.17(a).
(1) The certification under paragraph (a) of this section must be submitted no later than 10 business days after May 28, 2029; and
(2) The certification under paragraph (b) of this section must be submitted no later than 10 business days after May 25, 2032.
§ 751.509 - Other prohibitions and restrictions on the manufacturing, processing, distribution in commerce and commercial use of chrysotile asbestos.
(a) After May 27, 2026, all persons are prohibited from manufacturing (including importing), processing, distributing in commerce, and commercial use of chrysotile asbestos, including any chrysotile asbestos-containing products or articles, for use in sheet gaskets for chemical production, except as provided in paragraphs (b) and (c) of this section. Any sheet gaskets for chemical production which are already installed for use on May 27, 2026 are not subject to the distribution in commerce and commercial use prohibitions.
(b) Any person may commercially use chrysotile asbestos sheet gaskets for titanium dioxide production until May 28, 2029.
(c)(1)(i) Any person may commercially use chrysotile asbestos sheet gaskets for processing nuclear material until May 28, 2029.
(ii) Any person may commercially use chrysotile asbestos sheet gaskets for processing nuclear material at the Savannah River Site until December 31, 2037.
(2) After November 25, 2024, any person commercially using chrysotile asbestos sheet gaskets for processing nuclear material pursuant to (c)(1)(i) and (ii) must have in place exposure controls expected to reduce exposure of potentially exposed persons to asbestos, and provide potentially exposed persons in the regulated area where chrysotile asbestos sheet gasket replacement is being performed a full-face air purifying respirator with a P-100 (HEPA) cartridge (providing an assigned protection factor of 50), or other respirator that provides a similar or higher level of protection to the wearer.
(3)(i) Any sheet gaskets for processing nuclear material which are already installed for use on May 28, 2029 are not subject to the distribution in commerce and commercial use prohibitions in paragraphs (a) of this section.
(ii) Any sheet gaskets for processing nuclear material at the Savannah River Site which are already installed for use on December 31, 2037, are not subject to the distribution in commerce and commercial use prohibitions in paragraphs (a) of this section.
(d) After November 25, 2024, all persons are prohibited from manufacturing (including importing), processing, distribution in commerce and commercial use of chrysotile asbestos, including any chrysotile asbestos-containing products or articles, for commercial use of:
(1) Oilfield brake blocks;
(2) Aftermarket automotive brakes and linings;
(3) Other vehicle friction products; and
(4) Other gaskets.
(e) After November 25, 2024, all persons are prohibited from the manufacturing (including importing), processing, and distribution in commerce of chrysotile asbestos, including any chrysotile asbestos-containing products or articles, for consumer use of:
(1) Aftermarket automotive brakes and linings; and
(2) Other gaskets.
(f) On November 25, 2024:
(1) Any aftermarket automotive brakes and linings, other vehicle friction products, and other gaskets which are already installed for commercial use are not subject to the prohibitions on distribution in commerce and commercial use under paragraph (d) of this section.
(2) Any aftermarket automotive brakes and linings, and other gaskets which are already installed for consumer use are not subject to the distribution in commerce prohibition under paragraph (e) of this section.
§ 751.511 - Interim workplace controls of chrysotile asbestos exposures.
(a) Applicability. This section applies to processing and commercial use of chrysotile asbestos, including any chrysotile asbestos-containing products or articles, for chrysotile asbestos diaphragms in the chlor-alkali industry; and to the commercial use of chrysotile asbestos sheet gaskets for titanium dioxide production.
(b) Interim Existing Chemical Exposure Limit (ECEL). Beginning November 25, 2024, the owner or operator must ensure that no person is exposed to an airborne concentration of chrysotile asbestos in excess of the interim ECEL for chrysotile asbestos of 0.005 fibers (f)/cubic centimeter (cc) as an eight (8)-hour time-weighted average (TWA). Where an owner or operator cannot demonstrate exposure at or below the ECEL, including through the use of all technically feasible engineering controls or work practices as described in paragraph (e)(1) of this section, and has not demonstrated that it has appropriately supplemented with respiratory protection that complies with the requirements of paragraph (f) of this section, this will constitute a failure to comply with the ECEL.
(c) Exposure monitoring—(1) In general. (i) Owners or operators must determine each potentially exposed person's exposure from personal breathing zone air samples that are representative of the 8-hour TWA exposure of each potentially exposed person.
(ii) Representative 8-hour TWA of a potentially exposed person's exposure must be determined on the basis of one or more samples representing full-shift exposures for each shift for each potentially exposed person in each job classification in each work area.
(2) Initial exposure monitoring. No later than November 25, 2024 each owner or operator covered by paragraph (a) of this section as of May 28, 2024, must perform initial exposure monitoring of all potentially exposed persons.
(3) Periodic exposure monitoring. The owner or operator must establish an exposure monitoring program for periodic monitoring of exposure to chrysotile asbestos. If one or more samples representing full-shift exposures from the most recent exposure monitoring exceeds the ECEL (>0.005 f/cc 8-hour TWA), periodic exposure monitoring is required within three months of the most recent exposure monitoring. Otherwise, periodic exposure monitoring is required within six months of the most recent exposure monitoring.
(4) Additional exposure monitoring. The owner or operator must conduct additional exposure monitoring within a reasonable timeframe after there has been a change in the production, process, control equipment, personnel or work practices that may result in new or additional exposures above the ECEL or the owner or operator has any reason to suspect that a change may result in new or additional exposures above the ECEL.
(5) Method of monitoring. (i) Exposure monitoring samples must be personal breathing zone samples collected and analyzed using methods and quality control procedures described in Appendix A to 29 CFR 1910.1001, or as referenced in Appendix A to 29 CFR 1910.1001 (Appendix B to 29 CFR 1910.1001, OSHA method ID-160, or the NIOSH 7400 method).
(ii) Owners or operators must use exposure monitoring methods that conform with the OSHA Reference Method specified in Appendix A of 29 CFR 1910.1001 or an equivalent method. If an equivalent method is used, the owner or operator must ensure that the method meets the following criteria:
(A) Replicate exposure data used to establish equivalency are collected in side-by-side field and laboratory comparisons; and
(B) The comparison indicates that 90% of the samples collected in the range 0.5 to 2.0 times the ECEL or the lowest concentration possible have an accuracy range of plus or minus 25 percent of the OSHA Reference Method specified in Appendix A of 29 CFR 1910.1001 at a 95 percent confidence level as demonstrated by a statistically valid protocol. The NIOSH 7402 analytical method may be applied to adjust the analytical result to include only chrysotile asbestos.
(6) Notification of exposure monitoring results. (i) The owner or operator must, within 15 business days of receipt of monitoring results, notify each potentially exposed person of these results either individually in writing or by posting the results in an appropriate location that is accessible to all potentially exposed persons. The notice must be in plain language and understandable to all potentially exposed persons.
(ii) The written notification required by paragraph (c)(6)(i) of this section must include the corrective action being taken by the owner or operator to reduce exposure to or below the ECEL, wherever monitoring results indicated that the ECEL had been exceeded.
(d) Regulated areas—(1) Establishment. Beginning November 25, 2024 the owner or operator must establish regulated areas wherever airborne concentrations of chrysotile asbestos exceed, or there is a reasonable possibility that they may exceed, the ECEL.
(2) Demarcation. The owner or operator must demarcate regulated areas from the rest of the workplace in a manner that minimizes the number of persons who will be exposed to chrysotile asbestos.
(3) Access. The owner or operator must limit access to regulated areas to authorized persons or other persons required by work duties to be present in regulated areas.
(4) Provision of respirators. The owner or operator must supply a respirator selected in accordance with paragraph (f) of this section to each person entering a regulated area and must require the use of such respirator.
(5) Prohibited activities. The owner or operator must ensure that persons do not eat, drink, smoke, chew tobacco or gum, or apply cosmetics in the regulated area.
(e) Exposure Control Procedures and Plan—(1) Exposure Controls. (A) The owner or operator must institute engineering controls and work practices to reduce and maintain airborne chrysotile asbestos concentrations to or below the ECEL, except to the extent that the owner or operator can demonstrate that such controls are not feasible.
(B) Wherever the feasible engineering controls and work practices that can be instituted are not sufficient to reduce airborne chrysotile asbestos concentrations to or below the ECEL, the owner or operator must use them to reduce exposures to the lowest levels achievable by these controls. If the feasible engineering controls and work practices cannot reduce exposures to or below the ECEL, the owner or operator must supplement the controls by providing and requiring the use of respiratory protection that complies with the requirements of paragraph (f) of this section.
(2) Exposure Control Plan Requirements. (i) Beginning March 28, 2025, when the airborne chrysotile asbestos concentrations exceed the ECEL, or are reasonably expected to exceed the ECEL, owners and operators must establish and implement an exposure control plan to reduce exposures to all potentially exposed persons to or below the ECEL by means of engineering controls and work practices, and by the use of respiratory protection where required under paragraph (e)(1)(B) of this section. The exposure control plan must be available to persons exposed to chrysotile asbestos.
(ii) The exposure control plan must be reviewed and updated as necessary, but at least annually, to reflect any significant changes in the status of the owner or operator's compliance with the requirements of this section.
(iii) The owner or operator must not implement a schedule of personnel rotation as a means of compliance with the ECEL.
(iv) The exposure control plan must include:
(A) An explanation of the exposure controls considered, a rationale for why exposure controls were selected or not selected, based on feasibility, effectiveness, and other relevant considerations;
(B) Descriptions of actions the owner or operator must take to implement the exposure controls selected, including proper installation, maintenance, training, or other actions, and the estimated timeline for implementing such controls;
(C) Description of activities conducted by the owner or operator to review and update the exposure control plan to ensure effectiveness of the exposure controls, identify any necessary updates to the exposure controls, and confirm that all persons are properly implementing the exposure controls; and
(D) An explanation of the procedures for responding to any change that may reasonably be expected to introduce additional sources of exposure to chrysotile asbestos, or otherwise result in increased exposure to chrysotile asbestos, including procedures for implementing corrective actions to mitigate exposure to chrysotile asbestos.
(f) Respiratory protection—(1) Method of Compliance. Beginning November 25, 2024, if an owner or operator is required to provide respiratory protection pursuant to paragraphs (d)(4) or (e)(1)(B) of this section, the owner or operator must provide each potentially exposed person with a respirator according to the requirements of this section.
(2) Respirator program. For purposes of this paragraph (f)(2), the cross-referenced provisions in 29 CFR 1910.134 applying to an “employee” also apply equally to potentially exposed persons, and provisions applying to an “employer” also apply equally to owners or operators.
(i) Owners and operators must select respiratory protection that properly fits each affected person and communicate respirator selections to each affected person consistent with the requirements of 29 CFR 1910.134(f) and 1910.134 App. A.
(ii) Owners and operators must provide, ensure use of, and maintain (in a sanitary, reliable, and undamaged condition) respiratory protection that is of safe design and construction for the applicable condition of use consistent with the requirements of 29 CFR 1910.134(g) through (j) and 1910.134 App. B-1 to B-2.
(iii) Prior to or at the time of initial assignment to a job involving potential exposure to chrysotile asbestos, owners and operators must provide training and retraining to all persons required to use respiratory protection consistent with 29 CFR 1910.134(k).
(3) Respirator selection. Owners or operators must select and provide appropriate respirators based on the most recent exposure monitoring. The minimum respiratory protection that must be provided is as follows:
(i) If the most recent exposure monitoring indicates that the exposure concentration is at or below the 0.005 f/cc (ECEL): no respiratory protection is required.
(ii) If the most recent exposure monitoring indicates that the exposure concentration is above 0.005 f/cc (ECEL) and less than or equal to 0.05 f/cc (10 times the ECEL):
(A) A half-mask supplied-air respirator (SAR) or airline respirator operated in demand mode; or
(B) A half-mask self-contained breathing apparatus (SCBA) respirator operated in demand mode (Assigned Protection Factor 10).
(iii) If the most recent exposure monitoring indicates that the exposure concentration is above 0.05 f/cc (10 times the ECEL) and less than or equal to 0.125 f/cc (25 times the ECEL): A loose fitting facepiece supplied-air respirator (SAR) or airline respirator operated in continuous flow mode (Assigned Protection Factor 25).
(iv) If the most recent exposure monitoring indicates that the exposure concentration is above 0.125 f/cc (25 times the ECEL) and less than or equal to 0.25 f/cc (50 times the ECEL):
(A) A full facepiece supplied-air respirator (SAR) or airline respirator operated in demand mode; or
(B) A half-mask supplied-air respirator (SAR) or airline respirator operated in continuous flow mode; or
(C) A half-mask supplied-air respirator (SAR) or airline respirator operated in pressure-demand or other positive-pressure mode; or
(D) A full facepiece self-contained breathing apparatus (SCBA) respirator operated in demand mode; or
(E) A helmet/hood self-contained breathing apparatus (SCBA) respirator operated in demand mode (Assigned Protection Factor 50).
(v) If the most recent exposure monitoring indicates that the exposure concentration is above 0.25 f/cc (50 times the ECEL) and less than or equal to 5 f/cc (1,000 times the ECEL): A full-facepiece supplied-air respirator (SAR) or airline respirator operated in pressure-demand or other positive-pressure mode (Assigned Protection Factor 1,000).
(vi) If the most recent exposure monitoring indicates that the exposure concentration is above 5 f/cc (1,000 times the ECEL) and less than or equal to 50 f/cc (10,000 times the ECEL):
(A) A full-facepiece self-contained breathing apparatus (SCBA) respirator operated in pressure-demand or other positive-pressure mode; or
(B) A helmet/hood self-contained breathing apparatus (SCBA) respirator operated in pressure-demand or other positive-pressure mode (Assigned Protection Factor 10,000).
(vii) The respiratory protection requirements in paragraph (f)(3) of this section represent the minimum respiratory protection requirements, such that any respirator affording a higher degree of protection than the required respirator may be used.
(g) Workplace information and training. (1) By November 25, 2024, the owner or operator must institute a training program and ensure that persons potentially exposed to chrysotile asbestos participate in the program according to the requirements of this paragraph (g).
(2) The owner or operator must train each potentially exposed person prior or at the time of a potential exposure to chrysotile asbestos and at least annually thereafter.
(3) The owner or operator must ensure that information and training is presented in a manner that is understandable to each person required to be trained.
(4) The following information and training must be provided to all persons potentially exposed to chrysotile asbestos:
(i) The health effects associated with exposure to chrysotile asbestos, based on the most recent publication by EPA, OSHA, NIOSH, and/or CDC;
(ii) The quantity, location, manner of use, release, and storage of chrysotile asbestos and the specific operations in the workplace that could result in exposure to chrysotile asbestos, noting where each regulated area is located;
(iii) The specific procedures implemented to control exposures and manage occupational risks to persons potentially exposed to chrysotile asbestos, such as engineering controls, work practices and personal protective equipment to be used; and
(iv) The requirements of this section, as well as how to access or obtain a copy of these regulations.
(5) Whenever there are workplace changes, such as modifications of tasks or procedures or the institution of new tasks or procedures, or when the airborne concentration of chrysotile asbestos increases, or when the exposure control plan is updated according to paragraph (e)(2)(ii) of this section, the owner or operator must update the training and re-train each potentially exposed person.
§ 751.513 - Disposal.
(a) After November 25, 2024, all persons disposing of chrysotile asbestos and any chrysotile asbestos-containing products or articles subject to § 751.505, must dispose of chrysotile asbestos and any chrysotile asbestos-containing products or articles, as applicable:
(1) In accordance with the Asbestos General Industry Standard—(29 CFR 1910.1001(k)).
(2) In conformance with the asbestos waste disposal requirements at 40 CFR 61.150.
(b) After November 25, 2024, all persons disposing of chrysotile asbestos and any chrysotile asbestos-containing products or articles subject to paragraphs (a) through (c) of § 751.509 must dispose of chrysotile asbestos and any chrysotile asbestos-containing products or articles, as applicable:
(1) In accordance with the Asbestos Safety and Health Regulations for Construction—(29 CFR 1926.1101)
(2) [Reserved]
(c) After November 25, 2024, all persons disposing of chrysotile asbestos and any chrysotile asbestos-containing products or articles subject to § 751.509(d) must dispose of chrysotile asbestos and any chrysotile asbestos-containing products or articles, as applicable:
(1) In accordance with the Asbestos General Industry Standard—(29 CFR 1910.1001).
(2) In conformance with the asbestos waste disposal requirements at 40 CFR 61.150.
(d) After November 25, 2024, each manufacturer (including importer), processor, and distributor of chrysotile asbestos, including any chrysotile asbestos-containing products or articles, for consumer use, disposing of chrysotile asbestos and any chrysotile asbestos-containing products or articles subject to § 751.509(e), must dispose of chrysotile asbestos and any chrysotile asbestos-containing products or articles, as applicable:
(1) In accordance with the Asbestos General Industry Standard at 29 CFR 1910.1001(k).
(2) In conformance with the asbestos waste disposal requirements at 40 CFR 61.150.
§ 751.515 - Recordkeeping.
(a) General records. After November 25, 2024, all persons who manufacture (including import), process, or distribute in commerce or engage in commercial use of chrysotile asbestos must maintain ordinary business records, such as invoices and bills-of-lading related to compliance with the prohibitions, restrictions, and other provisions of this subpart.
(b) Certification of compliance for chlor-alkali industry records. Persons required pursuant to § 751.507 to certify compliance with § 751.505 must:
(1) Retain records of certifications prepared to comply with § 751.507 and records to substantiate such certifications; and
(2) Make the records retained pursuant to paragraph (b)(1) of this section available to EPA for inspection.
(c) Interim workplace controls of chrysotile asbestos exposures records—(1) Exposure monitoring. For each monitoring event, owners or operators subject to the exposure monitoring required by § 751.511(c) must document, retain records of the following and make them available to EPA for inspection:
(i) Dates, duration, and results of each sample taken;
(ii) The quantity, location(s) and manner of chrysotile asbestos use at the time of each monitoring event;
(iii) All measurements that may be necessary to determine sampling conditions that may have affected the monitoring results;
(iv) Name, address, work shift, job classification, work area, and type of respiratory protection (if any) of each monitored person;
(v) Sampling and analytical methods used and documentation of compliance with the quality control procedures described in § 751.511(c)(5)(i) and (ii); and
(vi) Notification of exposure monitoring results in accordance with § 751.511(c)(6).
(2) Other requirements. Owners or operators subject to the interim workplace controls described in § 751.511 must retain records and make them available to EPA for inspection of:
(i) The exposure control plan and its implementation as required by § 751.511(e).
(ii) Respiratory protection used and program implementation as described in § 751.511(f); and
(iii) Information and training provided by the owner or operator as required by § 751.511(g).
(d) Disposal records. Each person, except a consumer, who disposes of any chrysotile asbestos and any chrysotile asbestos-containing products or articles subject to § 751.513, after November 25, 2024 must retain in one location at the headquarters of the company, or at the facility for which the records were generated, documentation showing any records related to any disposal of chrysotile asbestos and any chrysotile asbestos-containing products or articles generated pursuant to, or otherwise documenting compliance with, regulations specified in § 751.513.
(e) Retention. The documentation in this section must be retained for 5 years from the date of generation.